Adhesive Bond and Tensile Performance of Scrap Inner Tube Rubber for Low-cost Seismic Base Isolation in Rural Housing

Authors

  • Harsono Harsono
    Affiliation
    Department of Civil Engineering, Faculty of Civil, Planning, and Geo Engineering, Institut Teknologi Sepuluh Nopember, Jl. Taman Alumni, Civil Engineering Building, ITS Campus, Keputih, Sukolilo, Surabaya 60111, Indonesia
  • Tavio Tavio
    Affiliation
    Department of Civil Engineering, Faculty of Civil, Planning, and Geo Engineering, Institut Teknologi Sepuluh Nopember, Jl. Taman Alumni, Civil Engineering Building, ITS Campus, Keputih, Sukolilo, Surabaya 60111, Indonesia
  • Gabriele Milani
    Affiliation
    Department of Architecture, Built Environment and Construction Engineering, Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milan, Italy
  • Dinis Pinto
    Affiliation
    Department of Civil Engineering, Faculty of Engineering, Universidade da Paz, Rua Osindo 1, Manleuana, Dili, Timor-Leste
  • Andrew Hartanto Jusuf
    Affiliation
    Department of Civil Engineering, Faculty of Civil, Planning, and Geo Engineering, Institut Teknologi Sepuluh Nopember, Jl. Taman Alumni, Civil Engineering Building, ITS Campus, Keputih, Sukolilo, Surabaya 60111, Indonesia
  • Halid Wamala
    Affiliation
    Department of Civil Engineering, Faculty of Civil, Planning, and Geo Engineering, Institut Teknologi Sepuluh Nopember, Jl. Taman Alumni, Civil Engineering Building, ITS Campus, Keputih, Sukolilo, Surabaya 60111, Indonesia
https://doi.org/10.3311/PPci.45124

Abstract

his study evaluated the adhesive bond and tensile response of scrap inner tube rubber as a preliminary material candidate for low-cost seismic isolation. Ten single-lap specimens bonded with a solvent-based polychloroprene adhesive were tested using a comparative joint configuration adapted from ASTM D1002: five untreated control specimens (CS) and five mechanically roughened specimens (RS). Using the confirmed bonded area of 322.58 mm2, surface roughening increased the average apparent lap-shear strength from 0.064 MPa to 0.167 MPa and the average failure displacement from 51.7 mm to 182.4 mm. Welch two-sample tests confirmed clear differences in apparent strength (mean difference 0.1029 MPa, 95% CI 0.0944–0.1113 MPa) and displacement (mean difference 130.7 mm, 95% CI 121.0–140.4 mm), both p < 0.001. Roughening also shifted joint failure from predominantly interfacial separation toward cohesive or mixed patterns. Five dumbbell rubber specimens were tested under uniaxial loading with reference to ASTM D412 Die C. The rubber reached an average tensile stress of 7.07 MPa and sustained an average crosshead displacement of 331 mm before rupture; elongation at break was not determined because no extensometer was used. These coupon-scale results establish preliminary material and joint feasibility; cyclic compression-shear, durability, process-control, source-variability, and component-level testing remain necessary.

Keywords:

base isolation, polychloroprene adhesive, recycled inner-tube rubber, resource efficiency, surface roughening

Citation data from Crossref and Scopus

Published Online

2026-11-17

How to Cite

Harsono, H., Tavio, T., Milani, G., Pinto, D., Jusuf, A. H., Wamala, H. “Adhesive Bond and Tensile Performance of Scrap Inner Tube Rubber for Low-cost Seismic Base Isolation in Rural Housing”, Periodica Polytechnica Civil Engineering, 2026. https://doi.org/10.3311/PPci.45124

Issue

Section

Research Article